Hey 3d printing people.
-
@demofox note that the part at the top looks fine. That is because the print head is moving less on the horizontal plane, which is causing the hot end to loose less heat. Usually you'd see the opposite problem (warping from running too warm) there.
@demofox To fix the hot end problem, try to make ambient temperature more steady. My favorite trick is to put a desk fan near by such that the hot end is always under constant airflow no matter what position the gantry and plate are in, and wait for the temperature to stabilize before you start printing. Build chambers are also popular for stabilizing the temperature, but they tend to run hot which can introduce its own problems. The critical thing is steady ambient temperature.
-
@demofox To fix the hot end problem, try to make ambient temperature more steady. My favorite trick is to put a desk fan near by such that the hot end is always under constant airflow no matter what position the gantry and plate are in, and wait for the temperature to stabilize before you start printing. Build chambers are also popular for stabilizing the temperature, but they tend to run hot which can introduce its own problems. The critical thing is steady ambient temperature.
@demofox as for the belt slip, lube up the rods
-
@demofox more things that could potentially help with the temperature problem since your printer for the most part seems to be running too cool:
- run it slower
- run it a little hotter
the air flow thing is the most important one though. you'll want to make sure the airflow is consistent first.
-
@demofox more things that could potentially help with the temperature problem since your printer for the most part seems to be running too cool:
- run it slower
- run it a little hotter
the air flow thing is the most important one though. you'll want to make sure the airflow is consistent first.
@demofox I scanned through the other replies, and I want to also note that the temperature thing is the more critical thing to diagnose first, since if a layer fails to bond properly it can warp and create an obstacle for the nozzle to crash into, which can cause belt slippage like in your print.
-
@demofox I scanned through the other replies, and I want to also note that the temperature thing is the more critical thing to diagnose first, since if a layer fails to bond properly it can warp and create an obstacle for the nozzle to crash into, which can cause belt slippage like in your print.
@aeva thank you so much! Interestingly, its still firmly attached to the raft, but maybe that is only in the center.
3d printing is quite involved apparently!
This is also a 50$ printer that is a year old so maybe not the best setup :P -
@aeva thank you so much! Interestingly, its still firmly attached to the raft, but maybe that is only in the center.
3d printing is quite involved apparently!
This is also a 50$ printer that is a year old so maybe not the best setup :P@demofox sure thing :) 3D printing is a bottomless dive of fascinating interconnected technical problems that can burn your house down. At the zenith of my 3D printing hobby I had four printers (two frankenprinters and two industrial prototypes), was writing my own custom slicing software, and had a salary from a 3D printer manufacturer. Then, for reasons, I burned out on that particular special interest and went off to live a simple life as a game developer.
-
@demofox sure thing :) 3D printing is a bottomless dive of fascinating interconnected technical problems that can burn your house down. At the zenith of my 3D printing hobby I had four printers (two frankenprinters and two industrial prototypes), was writing my own custom slicing software, and had a salary from a 3D printer manufacturer. Then, for reasons, I burned out on that particular special interest and went off to live a simple life as a game developer.
@demofox however, I appreciate the powerful chaotic energy of the phrase "fifty dollar three-dee printer"
-
@demofox however, I appreciate the powerful chaotic energy of the phrase "fifty dollar three-dee printer"
@demofox this was my first 3D printer https://mastodon.gamedev.place/@aeva/113516625532069448 I built it from a defective kit at an event at my local hackerspace back in 2011 ish, corrected the problems with the frame in software, used it to upgrade itself, and got pretty good prints out of it while I was still using it. The thing frequently needed to be recalibrated due to the frame bolts needing to be retightened periodically.
-
@demofox this was my first 3D printer https://mastodon.gamedev.place/@aeva/113516625532069448 I built it from a defective kit at an event at my local hackerspace back in 2011 ish, corrected the problems with the frame in software, used it to upgrade itself, and got pretty good prints out of it while I was still using it. The thing frequently needed to be recalibrated due to the frame bolts needing to be retightened periodically.
@demofox anyways what I mean to say is there is hope for your machine, it just might require a lot of tinkering
-
@demofox anyways what I mean to say is there is hope for your machine, it just might require a lot of tinkering
@demofox also fwiw I think there is still some value in starting with a janky printer and learning how to take proper care of it before moving on to an expensive one, because then you'll be better prepared to do maintenance on the expensive one when it inevitably has a problem, which it will, because all 3D printers are fundamentally cursed objects.
Feed RSS
Gli ultimi otto messaggi ricevuti dalla Federazione
-
@briankrebs call me old fashioned, but not being stuck in a layer cake plot is one of my favorite perks of traditional employment
-
Amicici e amicice del fediverso, non ricordo chi è il genio tra voi che scrive i post bilingui italo-veneto, ma questo post è dedicato soprattutto a lui
-
When should children have their #measles #vaccines?
From January 2026, the UK will offer the second dose of measles vaccine at the age of 18 months instead of at the age of three or four. The first dose will continue to be given at 12 months.
The move is inspired by research showing better vaccine uptake when the second dose of measles vaccine is offered earlier. France takes a similar approach, but there are a variety of schedules across Europe.
https://www.vaccinestoday.eu/stories/when-should-children-have-their-measles-vaccines/
-
This post did not contain any content.
-
Vibe merde
-
Spero tu stia bene, spero stiate bene tutti.
Buona notte Mohammed 🍉
-
@martellum Anche io.🤬
-
L’Italia rispetta l’illegalità internazionale.
Alle 16:30 di oggi la Nave Alpino della Marina Militare italiana ha comunicato che non accompagnerà oltre le 150 miglia nautiche dalla costa di Gaza le imbarcazioni della Flotilla e che alle ore 2:00 di stanotte invertirà la sua rotta.
Chiediamo ancora con tutta la forza possibile al Governo Italiano di recedere da questa decisione: tutelare l’incolumità degli equipaggi della Flotilla, e delle tante cittadine e cittadini italiani a bordo, è un dovere.
#GlobalSumudFlotilla
#BreakTheSiege
#FreePalestine
#SailToGaza
#GlobalMovementToGaza
