LA Times: Justice Department drafting a list of ‘domestic terrorists’
Uncategorized
6
Posts
2
Posters
0
Views
-
LA Times: Justice Department drafting a list of ‘domestic terrorists’
-
LA Times: Justice Department drafting a list of ‘domestic terrorists’
***this is going to be very, very bad (and probably very, very illegal), but it seems they are going to go after people who are against law enforcement abuse, ICE kidnappings, and also again the trans community, etc. 😬
-
***this is going to be very, very bad (and probably very, very illegal), but it seems they are going to go after people who are against law enforcement abuse, ICE kidnappings, and also again the trans community, etc. 😬
Yeesh, per LA Times:
"Law enforcement agencies are directed in the memo, dated Dec. 4, to identify “domestic terrorists” who use violence, or the threat of violence, to advance political and social agendas, including “adherence to radical gender ideology, anti-Americanism, anti-capitalism, or anti-Christianity.” "
-
Yeesh, per LA Times:
"Law enforcement agencies are directed in the memo, dated Dec. 4, to identify “domestic terrorists” who use violence, or the threat of violence, to advance political and social agendas, including “adherence to radical gender ideology, anti-Americanism, anti-capitalism, or anti-Christianity.” "
@ai6yr So, rat out your woke neighbor AND get paid. I'm sure this will go just fine.
-
@ai6yr So, rat out your woke neighbor AND get paid. I'm sure this will go just fine.
@mattblaze "anti-Christianity"... so, rat out anyone who isn't a Christian is a thing now too?
-
@mattblaze "anti-Christianity"... so, rat out anyone who isn't a Christian is a thing now too?
@ai6yr "I think my neighbor has a basement full of sans-serif fonts".
-
undefined oblomov@sociale.network shared this topic
Gli ultimi otto messaggi ricevuti dalla Federazione
-
Contro la casa di vetro. Opacità, schedatura e potere nell’età digitale. 17° Convegno Nexa su Internet & Società a Torino Lunedì 15 dicembre 2025
Lunedì 15 dicembre 2025
ore 9.00 – 18.00Sala Conferenze “Luigi Ciminiera”
DAUIN, Politecnico di Torino, 5° piano
Corso Castelfidardo 34/D, Torino (mappa)Hashtag del convegno: #nexa2025
Per motivi organizzativi, è gradita la segnalazione della propria partecipazione all’indirizzo: Mobilizon
Con @smaurizi @RL @RossellaLatempa @avetro e altri che non sono ancora su mastodon 😅
L’ingresso è libero e gratuito fino ad esaurimento posti.
-
@francina1909 ma la domanda corretta è?
Perché ci facciamo mille menate quando la nostra esistenza è una briciola nell'universo ?
Fra 10-20-30 anni non ci saremo più, fra 100 non saremo nemmeno ricordati, quindi godiamo del ora e adesso, siamo troppo piccoli per avere un impatto, pure minimo, su qualsiasi cosa. Tutto quello che ci fa stare bene è buono, quello che ci sta fare male è male, a prescindere.
Il resto serve solo ad ingrassare le tasche dei psicoanalisti...
-
Sud-est asiatico: scontri al confine thailandia-cambogia. cosa sta succedendo? il punto con la giornalista junko terao
@anarchia
Proseguono gli scontri lungo il conteso confine tra Thailandia e Cambogia in quello che è un conflitto che da decenni si trascina su una frontiera mai completamente delimitata. A luglio un’altra
-
Designing a Simpler Cycloidal Drive
Cycloidal drives have an entrancing motion, as well as a few other advantages – high torque and efficiency, low backlash, and compactness among them. However, much as [Sergei Mishin] likes them, it can be difficult to 3D-print high-torque drives, and it’s sometimes inconvenient to have the input and output shafts in-line. When, therefore, he came across a video of an industrial three-ring reducing drive, which works on a similar principle, he naturally designed his own 3D-printable drive.
The main issue with 3D-printing a normal cycloidal drive is with the eccentrically-mounted cycloidal plate, since the pins which run through its holes need bearings to keep them from quickly wearing out the plastic plate at high torque. This puts some unfortunate constraints on the size of the drive. A three-ring drive also uses an eccentric drive shaft to cause cycloidal plates to oscillate around a set of pins, but the input and output shafts are offset so that the plates encompass both the pins and the eccentric driveshaft. This simplifies construction significantly, and also makes it possible to add more than one input or output shaft.
As the name indicates, these drives use three plates 120 degrees out of phase with each other; [Sergei] tried a design with only two plates 180 degrees out of phase, but since there was a point at which the plates could rotate just as easily in either direction, it jammed easily. Unlike standard cycloidal gears, these plates use epicycloidal rather than hypocycloidal profiles, since they move around the outside of the pins. [Sergei] helpfully wrote a Python script that can generate profiles, animate them, and export to DXF. The final performance of these drives will depend on their design parameters and printing material, but [Sergei] tested a 20:1 drive and reached a respectable 9.8 Newton-meters before it started skipping.
Even without this design’s advantages, it’s still possible to 3D-print a cycloidal drive, its cousin the harmonic drive, or even more exotic drive configurations.
-
@mathewi@journa.host I'd say less that the social web is dying, it's quite alive and well on the Fediverse.
I'd argue that the social web as it currently stands is being abandoned by the very companies that made it.
-
@VE2UWY @AaronDavid was it ever "open-sourced"?
-
@simona devi solo smettere di seguire @underscorner e poi seguirlo di nuovo
-
@filippodb @lalchimistadigitale @spettacoli beh già nel 1985 non è che fosse così al top. È una produzione italiana al risparmio e non sono neppure così sicuro che abbia mai visto la pelle di un tamburo. Ma il groove, anche se sintetico, funziona e il ritmo vagamente in controtempo potrebbe addirittura ricordare (bestemmio) Blue Monday dei New Order
