New day, even more topstitching.
Uncategorized
15
Posts
3
Posters
27
Views
-
New day, even more topstitching. All the boning channel tapes are attached and properly sewn on two sides, and some of them are also sewn in the middle, thus creating two channels for the tiny little narrow synthetic whalebone.
Next: Unpicking all the bits I had to redo because it's kind of hard to tidily sew through so many layers of coutil and the thick tape, and also the basting threads. -
New day, even more topstitching. All the boning channel tapes are attached and properly sewn on two sides, and some of them are also sewn in the middle, thus creating two channels for the tiny little narrow synthetic whalebone.
Next: Unpicking all the bits I had to redo because it's kind of hard to tidily sew through so many layers of coutil and the thick tape, and also the basting threads.Currently containing the urge to make every single boning channel appear symmetrical from the right side. We'll see if I give into it once all the boning channels are actually on, certainly I could have them all done before making decisions about even more tactical unpicking!
-
Currently containing the urge to make every single boning channel appear symmetrical from the right side. We'll see if I give into it once all the boning channels are actually on, certainly I could have them all done before making decisions about even more tactical unpicking!
An ode to petersham binding instead of bias binding! Not only can you get petersham in almost any fibre you like, it's also much thinner and quite malleable, so you can stretch and squish it together like bias binding without all the bulk. This viscose one I'm using is also very pretty and you don't need to pin it to sew it on, at all. Just keep one edge on a line of stay-stitching or drawn line a distance from the raw edge, flip, stitch again, done!
-
An ode to petersham binding instead of bias binding! Not only can you get petersham in almost any fibre you like, it's also much thinner and quite malleable, so you can stretch and squish it together like bias binding without all the bulk. This viscose one I'm using is also very pretty and you don't need to pin it to sew it on, at all. Just keep one edge on a line of stay-stitching or drawn line a distance from the raw edge, flip, stitch again, done!
In any case, the top binding of the corset is in place, and I just need to finish a couple of the thread ends while I further procrastinate on preparing and putting in any of the boning. Not today!
-
In any case, the top binding of the corset is in place, and I just need to finish a couple of the thread ends while I further procrastinate on preparing and putting in any of the boning. Not today!
I have put in the boning! Honestly I hate this step, persuading the bones into the very tight channels always hurts my hands and I hate trying to contain the plastic prubble (plastic crud pulver crumble) created by the filing down of the sharp edges, wrestling the big roll of it and... Ugh. 😓
But yeah! Measured shorter than the finished channel, slipped into the boning tape, jiggled into place. Done. -
I have put in the boning! Honestly I hate this step, persuading the bones into the very tight channels always hurts my hands and I hate trying to contain the plastic prubble (plastic crud pulver crumble) created by the filing down of the sharp edges, wrestling the big roll of it and... Ugh. 😓
But yeah! Measured shorter than the finished channel, slipped into the boning tape, jiggled into place. Done.Oh yeah. And guess how many metres of boning I had to put into this very short corset for a rather small person, which is myself? Fucking almost five metres. Fucking hell. Corsets, not even once, unless you have 11 million moneys to pay someone else to do it!
-
Oh yeah. And guess how many metres of boning I had to put into this very short corset for a rather small person, which is myself? Fucking almost five metres. Fucking hell. Corsets, not even once, unless you have 11 million moneys to pay someone else to do it!
Relevant side note: If you don't want to put plastic inside your corset, there's always the option of buying individual length pre-finished spiral steel bones, which tend to come in lengths with 2cm intervals. You guess or draft in the best length for the pattern, buy those, and then fix them in place with functional embroidery called flossing. Spiral steel just works and feels different from faux whalebone (which can be very delicate and cut into any length) and will also rust eventually.
-
Relevant side note: If you don't want to put plastic inside your corset, there's always the option of buying individual length pre-finished spiral steel bones, which tend to come in lengths with 2cm intervals. You guess or draft in the best length for the pattern, buy those, and then fix them in place with functional embroidery called flossing. Spiral steel just works and feels different from faux whalebone (which can be very delicate and cut into any length) and will also rust eventually.
@sinituulia
I'm having a corset made for me (🥳). I didn't trust random plastic bones and I wasn't sure how to find synthetic whale, so I went metal. Also I have had corsets with metal bones, it's ok for me. No metal bones in Latvian shops, I ordered from Germany. I'm tall and the precut bones where too short, so I ordered 2 rolls spiral and 1 roll flat. And a maybe 100 caps to finish. They didn't have cuters tho, but sewist told me not to worry, she'll borrow from her other work. (cont'd) -
@sinituulia
I'm having a corset made for me (🥳). I didn't trust random plastic bones and I wasn't sure how to find synthetic whale, so I went metal. Also I have had corsets with metal bones, it's ok for me. No metal bones in Latvian shops, I ordered from Germany. I'm tall and the precut bones where too short, so I ordered 2 rolls spiral and 1 roll flat. And a maybe 100 caps to finish. They didn't have cuters tho, but sewist told me not to worry, she'll borrow from her other work. (cont'd)@sinituulia
I mean, she is a pro + she works in a big sewing supply shop, why not?Well... those cutters didn't not work! She went to sharpen them and the person sharpening them explained that no, it is not gonna work ever. Because random craft store cutters are softer than stainless steel corset bones. I'm not sure how she did it, but I'm planning to take leftover boning and visit a shop where construction tools are sold to buy myself a proper steel cutters.
Honesty found it delightful.
-
@sinituulia
I mean, she is a pro + she works in a big sewing supply shop, why not?Well... those cutters didn't not work! She went to sharpen them and the person sharpening them explained that no, it is not gonna work ever. Because random craft store cutters are softer than stainless steel corset bones. I'm not sure how she did it, but I'm planning to take leftover boning and visit a shop where construction tools are sold to buy myself a proper steel cutters.
Honesty found it delightful.
@laumapret I've used spiral steel before and do put in like two flats per every "whalebone" corset, they're just visually thicker (I think the narrowest is 7mm and usually they're wider than that, you can get the whalebone in 3mm and 5mm and wider) and feel a bit different. The spiral steel is much grippier than the whalebone so it's harder on the hands if your boning channels are a bit snug? I've also done the big roll of steels, and while the cutting is possible with some decent hardware aisle cutters it's not so nice on the hands, and what I really struggled with was putting on the end caps nicely. There's a specific pliers for that you sometimes see sold, but that's even more tools. 😄
I wouldn't want to do it with a Karvinen in the space though, that's a lot of tiny metal bits for him to consume.
-
@sinituulia
I mean, she is a pro + she works in a big sewing supply shop, why not?Well... those cutters didn't not work! She went to sharpen them and the person sharpening them explained that no, it is not gonna work ever. Because random craft store cutters are softer than stainless steel corset bones. I'm not sure how she did it, but I'm planning to take leftover boning and visit a shop where construction tools are sold to buy myself a proper steel cutters.
Honesty found it delightful.
@laumapret @sinituulia I've bought some cheap cutters from the hardware store designed to cut steel wire, and they make a big difference in how easy dealing with spiral steel boning is, even if they are very much not top of the line tools or anything.
for flat steels I still tend to use a dremel-like power tool (or ideally, get somebody else to use a dremel for me :D ) to cut and sand down the edges, but that's helped by the fact that we do have such a tool at home for various other reasons
I'm still using the two regular pliers and lots of cursing (the latter is an integral part of the procedure, right?) for the end caps, because being multicraftual (in a multicraftual household) means that we have lots of multipurpose tools, but I don't do enough corsets to justify yet another single purpose one.
-
@laumapret I've used spiral steel before and do put in like two flats per every "whalebone" corset, they're just visually thicker (I think the narrowest is 7mm and usually they're wider than that, you can get the whalebone in 3mm and 5mm and wider) and feel a bit different. The spiral steel is much grippier than the whalebone so it's harder on the hands if your boning channels are a bit snug? I've also done the big roll of steels, and while the cutting is possible with some decent hardware aisle cutters it's not so nice on the hands, and what I really struggled with was putting on the end caps nicely. There's a specific pliers for that you sometimes see sold, but that's even more tools. 😄
I wouldn't want to do it with a Karvinen in the space though, that's a lot of tiny metal bits for him to consume.
@sinituulia @laumapret very not Karvinen safe, indeed! -
@laumapret @sinituulia I've bought some cheap cutters from the hardware store designed to cut steel wire, and they make a big difference in how easy dealing with spiral steel boning is, even if they are very much not top of the line tools or anything.
for flat steels I still tend to use a dremel-like power tool (or ideally, get somebody else to use a dremel for me :D ) to cut and sand down the edges, but that's helped by the fact that we do have such a tool at home for various other reasons
I'm still using the two regular pliers and lots of cursing (the latter is an integral part of the procedure, right?) for the end caps, because being multicraftual (in a multicraftual household) means that we have lots of multipurpose tools, but I don't do enough corsets to justify yet another single purpose one.
@valhalla @laumapret The little end cap pliers make it look so easy and fast, but I've never tried them! But yeah, pretty single purpose 😅
-
@valhalla @laumapret The little end cap pliers make it look so easy and fast, but I've never tried them! But yeah, pretty single purpose 😅
@sinituulia @valhalla
As I do not own any Karvinens, I was thinking that generic steel wire cuters might find some use in this household. Maybe my SO also needs to cut some wires or smth... but dremel seems a bit excessive. Then again, there are several HEMA people in my DnD guild, I think they had at least one dremel between all of them for swords. Next time I might ask them... -
@sinituulia @valhalla
As I do not own any Karvinens, I was thinking that generic steel wire cuters might find some use in this household. Maybe my SO also needs to cut some wires or smth... but dremel seems a bit excessive. Then again, there are several HEMA people in my DnD guild, I think they had at least one dremel between all of them for swords. Next time I might ask them...@laumapret @sinituulia not a real dremel, a dremel-like tool (bought for 25 € :) ), which arount here gets used mostly to cut various things for creative or repair purposes (PCBs, tubes and strips of plastic and metal, etc.)
but if you can get access to a shared real dremel that's even better!
Feed RSS
Gli ultimi otto messaggi ricevuti dalla Federazione
-
me who was an idiot - should just have said "object storage", s3 is what amazon call their object storage provider.
-
@aeva 1 TB seems to be 3.20 EUR per month: https://www.hetzner.com/storage/storage-box/
There are probably similar offers from other companies as well, because offsite backups at a different provider are a common requirement for professional deployments.
OVH also has something, but their website is confusing, rather than a base price they charge per GB and month.
-
@aeva after a lot of looking my answer to this was crickets
but I have two not-quite-adequate-but-still-worth-mentioning solutions
there's several nextcloud vendors that have pretty decent prices, I rent my stuff from hetzner, about $5/month for 1TB of storage. if you don't know nextcloud, think "open source dropbox"
but for my projects, what I settled on is a private forgejo instance. I have a little home cluster with 2TB in RAID1, and offsite backups at two different locations...
and the only reason I can justify the maintenance cost of setting up and doing all this is because my particular brand of autism inexplicably classifies all this work into "leisure activities"...
but yeah, if you happen to find a way to self host something like this, I can tell you it's going to be very snappy. if you've ever thought: "git doesn't work with binary assets files for games", that's just because you didn't have a full instance to yourself
-
@aeva yeah god
also like. my history isn't in reality linear, right? like I'll try something and then I look at it and it's shit. so I go back a revision or two and start again and next time I save I probably save with whatever number is next up
the linear history doesn't really reflect that
-
@finnmyrstad @pluralistic Dette er fantastisk! Gratulerer med helt nydelig video! Godt å se at forbrukerrådet er på ballen! Denne kommer jeg til å spre for alt det er verdt.
-
@aeva Backblaze, it's cheap as hell, you can encrypt your storage and the first 10gb is free
I have 100GB sitting in it and it costs me $1 a month inc. tax
-
The video itself is pretty shitty. How it "informs" about enshittification without even using the c-word (capitalism) makes me wonder: is this a conscious choice (if so: what's the rationale behind this choice?) or a lack of consciousness?
