I have resumed the folly of 3d printing after a nearly year long hiatus
Uncategorized
43
Posts
2
Posters
0
Views
-
new extruder motor has arrived. hopefully I'll be feeling well enough to install it sometime in the next decimillennium
new extruder (hardware & servo motor) installed, along with new bowden tube. lets see if this works
-
new extruder (hardware & servo motor) installed, along with new bowden tube. lets see if this works
pi has stopped reporting undervoltage. I haven't touched anything with that setup since yesterday. the fuck?
-
pi has stopped reporting undervoltage. I haven't touched anything with that setup since yesterday. the fuck?
Seems pretty good.
My z-alignment is still fucked. I printed this on a raft because I knew it still was, but the raft was nearly impossible to remove. it was WELDED to the build plate.
-
Seems pretty good.
My z-alignment is still fucked. I printed this on a raft because I knew it still was, but the raft was nearly impossible to remove. it was WELDED to the build plate.
I'm not sure if I need to adjust my z-offset in the ender 5 plus's touchscreen or if that only applies to printing natively with the printer, and I need to change it in my slicer. or in octoprint! there's a lot of places! (there's too many fucking places!)
-
I'm not sure if I need to adjust my z-offset in the ender 5 plus's touchscreen or if that only applies to printing natively with the printer, and I need to change it in my slicer. or in octoprint! there's a lot of places! (there's too many fucking places!)
and keep in mind that's me saying it as someone who has made it their livelong profession and hobby of touching computers as much as they can. I love a bunch of little places to change things. I love being able to fiddle with settings.
3d printing has too many settings
-
and keep in mind that's me saying it as someone who has made it their livelong profession and hobby of touching computers as much as they can. I love a bunch of little places to change things. I love being able to fiddle with settings.
3d printing has too many settings
fiddled with my z-offset calibration. tried measuring the build plate: that was a mistake. The thing is bent as fuck.
but it does do a 4x4 grid for level so maybe it can compensate enough for that to not be a huge problem. Lets see, time for another 9 hour print!
-
fiddled with my z-offset calibration. tried measuring the build plate: that was a mistake. The thing is bent as fuck.
but it does do a 4x4 grid for level so maybe it can compensate enough for that to not be a huge problem. Lets see, time for another 9 hour print!
it failed. it did a couple layers and then clogged. I went in there and the hot end was just hovering over the beginning of the print, while the extruder clicked.
-
it failed. it did a couple layers and then clogged. I went in there and the hot end was just hovering over the beginning of the print, while the extruder clicked.
and the undervolting is back. while the octopi isn't even connected to the printer (because I accidentally left the USB disconnected)
-
and the undervolting is back. while the octopi isn't even connected to the printer (because I accidentally left the USB disconnected)
Okay I thought I fixed the clog and turned up the print temp and did another Calicat. At the end of the print, the webcam showed nothing there. I watched the time-lapse, and yep. No filament at all came out.
So I've got something way more broken than just a low temperature
-
Okay I thought I fixed the clog and turned up the print temp and did another Calicat. At the end of the print, the webcam showed nothing there. I watched the time-lapse, and yep. No filament at all came out.
So I've got something way more broken than just a low temperature
replaced the filament that had snapped off just inside the extruder. it's printing again
-
replaced the filament that had snapped off just inside the extruder. it's printing again
it made it like 3 hours into an 9-48 hour print and stopped extruding again. I bet it snapped off once more
-
it made it like 3 hours into an 9-48 hour print and stopped extruding again. I bet it snapped off once more
This bowden tube does seem kinda crap, but I wonder if it's my filament? this has only been open a week, but maybe it was just brittle to begin with
-
This bowden tube does seem kinda crap, but I wonder if it's my filament? this has only been open a week, but maybe it was just brittle to begin with
@foone I bought "medical grade" Bowden tubing awhile back because it was much cheaper per metre than sold by 3D print places, but it wasn't good enough. If the weather has been humid, a week could be enough to mean you need to dry the filament.
-
undefined Oblomov shared this topic on
Gli ultimi otto messaggi ricevuti dalla Federazione
-
Che poi, spacciano per Made in Italy ciò che non lo è, ma il vero Made in Italy costa. Gli italiani, in massa, hanno perso la capacità di capire la qualità, quindi vanno di schifezze a prezzi bassissimi. Il Casentino ti dura una vita ma costa. Quando avranno capito che il low cost non esiste perché qualcuno il prezzo lo paga, la filiera italiana sarà morta e sepolta. Amen.
-
@Linkshaender
che meraviglia!
buonanotte Armin 🌌
-
•
frugando nella scatola dei ricordi 🐾«la Mimì col Trottola»
mag.1991
-
@thatgiga
La perfezione ❤️
-
@Otttoz ecco finalmente spiegato il famoso detto "abitare nel culo del mondo"!
-
@ibrahim46 @aral
L'Italia è con voi 🍉🍉
-
Il tutto sempre oltre Happy🦋, che è molto oltre il "semplice" journaling...
---
Happy🦋 è il diario della felicità che ho creato e che vorrei compilare tutti i giorni
Agevolo linkino per chi ne vuole sapere di più → https://adriananselmo.it/happy-mappa-gratitudine-felicita/Per domande sono qui!
-
Nuovo "giochino": riassumere i mesi solo con sticker. Sembra tutto così futile, eppure è liberatorio: un modo per dire cose serie in modo leggero.
