In paese c'è il gazebo della Lega strapieno di gente manco regalassero bomboloni, e io inizio a prepararmi mentalmente a straperdere anche le prossime elezioni regionali.
Uncategorized
2
Posts
2
Posters
0
Views
-
In paese c'è il gazebo della Lega strapieno di gente manco regalassero bomboloni, e io inizio a prepararmi mentalmente a straperdere anche le prossime elezioni regionali.
-
In paese c'è il gazebo della Lega strapieno di gente manco regalassero bomboloni, e io inizio a prepararmi mentalmente a straperdere anche le prossime elezioni regionali.
@phab Deus vult 🙂
Gli ultimi otto messaggi ricevuti dalla Federazione
-
@thorstenzoeller it was calm, but just for a few minutes. Then, a thunderstorm
-
@omar you're right. A thunderstorm arrived a few minutes later.
-
This is truly unheard!
"503 Service Unavailable
No server is available to handle this request. "
From slashdot.org 😭😱😱😭😭 the sky is falling! 😜 #slashdot #down
-
Protestare contro il genocidio palestinese diventerà reato ! Indispensabile mobilitarsi subito !
@anarchia
INTANTO MOBILITIAMOCI CONTRO LA VERGOGNOSA PARTITA ITALIA-ISRAELE PREVISTA A UDINE IL 14 OTTOBRE
https://www.rivoluzioneanarchica.it/protestare-contro-il-genocidio-palestinese-diventera-reato-indispensabile-mobilitarsi-subito/
-
@stefano won't be silent that long, beautiful :)
-
Removing Infill to Make 3D Printed Parts Much Stronger
When it comes to FDM 3D prints and making them stronger, most of the focus is on the outer walls and factors like their layer adhesion. However, paying some attention to the often-ignored insides of a model can make a lot of difference in its mechanical properties. Inspired by a string of [Tom Stanton] videos, [3DJake] had a poke at making TPU more resilient against breaking when stretched and PLA resistant to snapping when experiencing a lateral force.
Simply twisting the TPU part massively increased the load at which it snapped. Similarly, by removing the infill from the PLA part before replacing it with a hollow cylinder, the test part also became significantly more resilient. A very noticeable result of hollowing out the PLA part: the way that it breaks. A part with infill will basically shatter. But the hollowed-out version remained more intact, rather than ripping apart at the seams. The reason? The hollow cylinder shape is printed to add more walls inside the part. Plus cylinders are naturally more able to distribute loads.
All of this touches on load distribution and designing a component to cope with expected loads in the best way possible. It’s also the reason why finite element analysis is such a big part of the CAD world, and something which we may see more of in the world of consumer 3D printing as well in the future.
If you want stronger prints, be sure to check out brick layers. Or, consider adding a little something extra.
-
@arclight I'm just a hobby programmer but I'm looking forward to reading the book.
-
Quarkrotto (@quarkrotto.bsky.social)
https://bsky.app/profile/quarkrotto.bsky.social/post/3m2yfot5gos2c
Post suggeriti
-
Removing Infill to Make 3D Printed Parts Much Stronger'nWhen it comes to FDM 3D prints and making them stronger, most of the focus is on the outer walls and factors like their layer adhesion.
Uncategorized
1
-
Quarkrotto (@quarkrotto.bsky.social)'nhttps://bsky.app/profile/quarkrotto.bsky.social/post/3m2yfot5gos2c
Uncategorized
1
-
-
