Though this photo is already ten years old, it still carries the very same emotions I felt the moment I captured it.#MeerMittwoch #SeaWednesday #Photography #Photo #Sea
Uncategorized
3
Posts
2
Posters
14
Views
-
Though this photo is already ten years old, it still carries the very same emotions I felt the moment I captured it.
-
Though this photo is already ten years old, it still carries the very same emotions I felt the moment I captured it.
Wow. I love the grainy look and the palette.
-
@angel thank you!
-
undefined Oblomov shared this topic on
Gli ultimi otto messaggi ricevuti dalla Federazione
-
@stefano probably both 😅
-
Does 3D-Printed Foam Make Good Custom Tires?
Wouldn’t it be nice to 3D print an entire custom tire for small robots? It sure would, so [Angus] of [Maker’s Muse] decided to investigate whether nifty new filaments like expanding TPU offer anything new in this area. He did more than just print out a variety of smooth tires; he tested each with a motorized platform attached to a load cell, driving on a dusty sheet of MDF to simulate the average shop floor, or ant weight combat robot arena.
Why bother making your own wheels? As [Angus] points out, when one is designing their own robots from scratch, it’s actually quite difficult to find something off the shelf that is just the right size. And even if one does find a wheel that is just right, there’s still the matter of fitting it to the shaft. Things would be so much easier if one could simply 3D print both wheel and tire in a material that performs well.
Like TPU, but squishier.
Here’s what he found: Siraya Tech’s TPU air filament (about 70A on the Shore hardness scale) performed the best. This is TPU plus a heat-activated additive that foams up during extrusion, resulting in a flexible print that looks and feels more like foam than usual TPU. It makes a promising tire that performs as well as it looks. Another expanding filament, PEBA air (also from Siraya Tech) didn’t look or perform as well, but was roughly in the same ballpark.Both performed better than the classic DIY options of 3D-printed plain TPU, or laser-cut EVA foam. It’s certainly a lot less work than casting custom tires.
What about adding a tread pattern? [Angus] gave it a try. Perhaps unsurprisingly, a knobby tire has worse traction compared to a smooth tire on smooth MDF. But sometimes treads are appropriate, and as [Angus] points out, if one is 3D printing tires then adding treads comes at essentially zero cost. That’s a powerful ability.
Even if you are not interested in custom wheels, that foaming TPU filament looks pretty nifty. See for yourself in the video, embedded just below. If you find yourself finding a good use for it, be sure to drop us a tip!
-
Tutto bello, bravi i ragazzi, belle le musiche, buono il concerto.
Però tornare a casa da solo da Bellinzona è s[ata una pizza infinita.
-
Ghiglia ha chiesto lo stop sul servizio di Report che lo ritrae mentre va da Arianna Meloni. Ranucci: “Gravissimo”
@giornalismo
articolo21.org/2025/11/ghiglia…
Agostino Chiglia, membro del Garante
-
Trovato a Palermo a caso
-
@max anche a me sembra così , ora riesco a cogliere emozioni che allora mi sfuggivano
-
Più divento... ehm... "grande"... più mi sembra di sentire nelle sue canzoni qualcosa che all'epoca mi era sfuggito.
-
I realized my job could be done by a sign. Leaving now!
Post suggeriti
-
Having fun this morning with autumn colours and camera movement.'n#photography #PhotoOfTheDay #darktable #italy #italia #nature #ICM #photo #autumn #naturephotography
Uncategorized
1
-
-
Sauvées...Trouvées dans une brocante, il y a longtemps et immédiatement adoptées dans l'atelier...'n#photography #portrait #workshop #atelier
Uncategorized
1
-
From today's walk...'n#Photography #Fungi #Foraging #FungiFriday #Forest #APSC #Rangefinder #SamsungNX #NX300 #16mm #PancakeLens
Uncategorized
4
